How do I fix error code P0501?
What repairs can fix the code P0501?
- Repair or replace any non-corroded connections.
- Check the voltage of the VSS sensor and check the requirements of the manufacturer. If not, replace it.
- Replace the back end or transmission of the VSS.
- Clean up metal particles, remove codes and do a road test for the car.
How do I fix my P0500?
What repairs can fix the P0500 code?
- Vehicle speed sensor drive gear replaced.
- Repair or replacement of the wiring harness.
- Vehicle speed sensor replaced.
- Poor electrical connection resolved.
What does P0503 mean?
Vehicle Speed Sensor Intermittent/Erratic/High
P0503 is a diagnostic trouble code (DTC) for “Vehicle Speed Sensor Intermittent/Erratic/High”. This can happen for multiple reasons and a mechanic needs to diagnose the specific cause for this code to be triggered in your situation.
What can cause P0500?
What can cause the P0500 engine code? A P0500 engine code is caused by no data or incorrect data being sent to the ECM from the VSS. A damaged or faulty speed sensor is normally to blame for this. The VSS is attached to the transmission and records the power generated to determine how fast the car is traveling.
What is the VSS sensor?
The Vehicle Speed sensor or VSS measures transmission/transaxle output or wheel speed. The ECM uses this information to modify engine functions such as ignition timing, Air/Fuel ratio, transmission shift points, and to initiate diagnostic routines.
What is code P0502?
A P0502 code set by your vehicle’s powertrain control module indicates a possible issue with your vehicle speed sensor (VSS) or its circuit. This device monitors your vehicle speed so that the PCM can properly adjust functions, such as torque converter clutch lock up and shift scheduling.
What is P0501 code?
What the P0501 code means. P0501 is an OBD-II generic code that the engine control module (ECM) got an input from the vehicle speed sensor (VSS) that is out of range or an erratic voltage output that is not stable or smooth, with movement up or down.
How much does it cost to replace a speed sensor?
The average cost for vehicle speed sensor replacement is between $275 and $318. Labor costs are estimated between $116 and $146 while parts are priced between $159 and $172. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location.
How do I fix error code P0600?
How To Correct P0600 Serial Communication Link
- Replacing the Engine Control Unit.
- Carefully inspect the reason for low battery voltage and diagnose them clearly.
- Replacement of the ECU wiring harness or repairing the damaged part.
- If you come across any electrical connections that is poor repair them immediately.
Where is the speed control sensor located?
Hello, the speed sensor for the speedometer is located on the transmission at the rear extension housing. The housing is the part that the driveshaft slip yoke (front part of driveshaft) would be position at. The sensor is attached with a bolt that needs to be removed, it has a two wire connector going to it.
What is the code for a bad speed sensor?
What Does the P0500 Code Mean? Diagnostic trouble code (DTC) P0500 stands for “Vehicle Speed Sensor (VSS) Malfunction.” This code is set when the PCM or engine control module (ECM) detects incorrect speed readings or no signal at all from the vehicle speed sensor (VSS).
What is code P0501?
P0501 is an OBD-II generic code that the engine control module (ECM) got an input from the vehicle speed sensor (VSS) that is out of range or an erratic voltage output that is not stable or smooth, with movement up or down.
What causes a p0501 DTC code on a Dodge Ram?
A P0501 DTC trouble code may be caused by one or more of the following: The Vehicle Speed Sensor (VSS) is not reading (functioning) properly. There is a broken/frayed wire leading to the vehicle speed sensor.
What does the OBD-II code p0501 mean?
P0501 Vehicle Speed Sensor Range/Performance OBD-II Trouble Code Technical Description. Vehicle Speed Sensor “A” Range/Performance. This diagnostic trouble code (DTC) is a generic powertrain code, which means that it applies to OBD-II equipped vehicles, including but not limited to Honda, Proton, Kia, Dodge, Hyundai, VW, Jeep, etc.
How much does it cost to diagnose p0501 Volkswagen code?
The cost of diagnosing the P0501 VOLKSWAGEN code is 1.0 hour of labor. The auto repair labor rates vary by location, your vehicle’s make and model, and even your engine type.